I NEED TO NO IF THERE ARE ANY SONY T.V. REPAIR PEOPLE IN TH DAYTON OHIO AREA?

JP, Awesome! After months of pounding on the TV to keep the screen on, I tried your advice. On the KV-35, the lower screw is called creep, but is located in the same place at the end of the red cable. Turned it 1/8 of a turn clockwise and the screen had diagonal lines. Backed if off to 1/16 of a turn, and the screen was able to stay on. Hopefully, this will keep working for a while and keep this 250lb lead boat anchor out of the landfill. PS for Sandi, you need to remove all the screws in back of set in screwholes with => arrows, and then remove three more screws above the AV connectors, then pull the back out. Please exercise common sense and good electrical practice (safer to keep TV unplugged when touching insides), or else don't do it. Dave

Hello, I've got a Sony KV32TW77 and the set just died one night (no picture no audio). I've done some searching and I can say this much after taking the board module out. 1. Tested I/P voltage up to fuse = 120VAC 2. Tested I/P voltage for RY602 which should be 12VDC but found zero volts. 3. Lifted RY602 from board and supplied 12VDC and relay made contact, so it works. So I'm not getting the 12VDC req. to RY602 to get the req. 170VDC B+ Hummm...I'll keep looking....need some schematics and/or service manual or any trible knowledge to help me. TIA, Roy

Hi JP, I am not sure if you have fixed your set yet, but just in case you are still trying here is some info. Most of SONY Trinitrons from this series have common problem with bad solder joints on power supply board. I have replied to many people here who have similar problems. If you do a search on this forum using SONY TV or KV32 as keywords or my name you can find many of my posts for people with similar problems. It sounds like you have a failing joint on one of the components in Horizontal Output Transistor (HOT) Drive circuit. I would recommend not turning on your TV until it is fixed, because it can lead to failure of HOT and other components due to arcing on bad solder joints. A good starting point would be obtaining a Service Manual or at least a schematic. Again, I have already replied to other people with info where to download it on the web free of charge. Good luck, Jack

KV32TW77 Same exact symtoms. Except for some reason - Picture only went out for commercials & then came on for the show. Any solutions?

TENGO PROBLEMAS CON LA FUENTE CONMUTADA ,DESEARIA OBTENER AYUDA DE USTEDES ENVIANDOME EL PLANO DEL TE SONY KV-27V10 GRACIAS

I am having a similar problem with my32" trinitron. can you tellmeifyouevergottheproblem solved.

I am researching for a friend with same problem,but his stays black screen.After a 20 min. warm up still nothing. If you could direct us in the right direction, I will do the same if I find out anything. Thank you for your time.

I am having other problems than those listed in all the emails. Knowing I turned my Trinitron off the night before, I got up twice this week to the TV on, playing..... snow. Last night while watching it, it when to snow. I turned it off...made a squeaking noice. When I turned it back on, the Guideplus screen appears and I can not do anything else with it. Help!

Hey.. Just wanted to check in and see how my club was doing, cause it looks like I'm joining you! My parents Trinitron is doing the same thing. When you first turn the Television on, it takes extremely long for the warm-up period to end.. They end up leaving it on now to avoid waiting 30 minutes to watch television. Then, during playing my Gamecube, I realized it will flicker yet when I blow stuff up... In other words, when I'm playing my video game and I make a lot of light appear suddenly on the screen, the TV doesn't like that either, and it goes buh-bye.. Just like this damn sony is about to go.. buh-bye! =/