PECHORIN'S home   account   archive   eshop   globalmediapro
.
.


Post new message


Home

JVC service or questions

Stacy Sample Posted Jan 31, 2004

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better. Stacy Sample JVC Service & Engineering Houston, Texas

Reply

Share |
6,445 comments, pages:   « 1 2 3 547 548 549 550 551 552 553 643 644 645 »

    I have a JVC Tv that is a K Series that I bought in Germany. When I brought it back to the states all the channels are messed up. All the chanels are off by at least 1 chanel. for example, Fox Sports is suppose to be 30 but it is 31. How do I go into the setup and set all the channels to what they are suppose to be? Thanks

    Reply

    Re: JVC service or questions

     Gregg Posted Jan 04, 2005

    I have a JVC GR-AXM4U camcorder. I am getting an intermittent 03 error code and a tape end message even at the middle of a tape.

    Reply

    I have a camcorder GR-AXM250.When it is connected two line parallel discontinuous appear on the the screen, if this is in way to reproduce and the TBC (time base corrector) is disconnected they disappear, but if this in recording remains and they are recorded. How I can resover this. problem. Thanks Jorge

    Reply

    I Have a camcorder GR-AXM250, when I connect the camera in the screen appear two line vertical discontiuas so if it is record or it reproduce (play), when I disconnect the TBC (time base corrector) in the reproduction it disappear, but if I record they remain. How can I fix that problem. Thanks and Regards

    Reply

    Re: JVC service or questions

     JESSIE Posted Jan 04, 2005

    My JVC camcorder: GR-AXM225 turns on but it doesn't show any picture on the LCD, instead it flashes the message which says "LENS COVER" (even if the lens cover is totally opened). What could be the problem with it?

    Reply

    Re: JVC service or questions

     Ghatge Posted Jan 03, 2005

    Hi Stacym, I ve a JVC Mini component System Model No. MX-D402T, and I am looking it's spares in india. Do u ve any adrress or contact where I can get it? I need it's power amplifier card , which was burned due to over voltage. Thanks and Regards

    Reply

    Hi I've a problem with my JVC GR-DVL 9000. The little indication for condesation has appear and the Camcorder turns off. I haven't been out in bad wheater or airconditioned rooms etc. I had the camera in a cabinet for two month and when i took it out this alarm has appear. -Quest: Can i reset this alarm manually (i've tested the reset button without any response). Thank you in advance Tom C

    Reply

    Re: JVC service or questions

     jal Posted Jan 03, 2005

    Hi, I have handycam #GR D50 purchased in Dubai in feb'2003(i got worldwide warrty also with this) my problem is that the camera is not capturing object/scenery from last 20 days, it shows only junking lines on the LCD while shoot, no picture is dislpaying/recording , but its playing the DV cassete clearly..., what may be the problem for this....? can u give me your Mumbai office Service Centre Phone# or address or email, so i can get it repaired before my warrty expires... pls assist me ASAP. thanx n regards

    Reply

    Re: JVC service or questions

     Joe Posted Jan 03, 2005

    hi there, I turned on my tv today to only see a white screen shaped like an eye(you can only see this when the lights in the room are off other wise screen is black) and can still hear sound.. I am sorry I am not sure what model it is. thank you very much joe gaudon

    Reply

    I have a GR-D90U camcorder and when I turn it on everything is black except when it has sunlight and it will sometimes eventually work properly but it takes awhile and it does not always work. What should I do?

    Reply

Pages:   « 1 2 3 547 548 549 550 551 552 553 643 644 645 »



  


© 2001-2012 - Pechorin's - Contact Us - Report a bug

Pechorin's does not take responsibility for the content of the messages published in the Forum.

RSS feed