PECHORIN'S home   account   archive   eshop   globalmediapro
.
.


Post new message


Home

JVC service or questions

Stacy Sample Posted Jan 31, 2004

Assistance with JVC product

If anyone has a question regarding a problem with thier JVC product (error codes, safeguard mode etc) write me for troubleshooting assistance. Please provide your model # if available and note this site so I can assist you better. Stacy Sample JVC Service & Engineering Houston, Texas

Reply

Share |
6,445 comments, pages:   « 1 2 3 523 524 525 526 527 528 529 643 644 645 »

    Re: JVC service or questions

     nick Posted Feb 08, 2005

    HI I HAVE A JVC VCR THE MODEL IS HR-S6700U I HAVE A PROBLEM WITH THE DISPLAY WHEN I TURN THE UNIT OFF THE CLOCK DISPLAY IS VERY DIM TO THE POINT WERE YOU CAN BEARLY SEE IT IN THE DARK. WHEN I TURN THE UNIT ON THE DISPLAY WORKS FINE. OTHER THAN THIS PROBLEM THE VCR WORKS GREAT. DO YOU HAVE ANY IDEA WHAT THIS MIGHT BE?

    Reply

    Hello I have a JVC RX-660VBK Surround reciever The rear speakers won't work or the active sub . . front speakers work but with not muc volume centr speaker works If turnin gon ra speaker in Logic mode cancs out alll sound. . . The controls al work vol. front and rea controlsas wll mode setting also works. . Are thre multi fuse in side unit that might be replaced or anythg that might need to b plugged. Theinsidof amp loks lke thereare cards installed in to a circut baord. . Also amp doesn't sound lke a 100 watt channel amp . Is the 100watts a rea 100watts per channle ? I also can't get a ser or usermanauls for downlaod either Speakers I'm using pair of Wharfedale at 50 wats a speaker rear speakers Sanyo 40 watts centr smal radio scach driver rated at 40 wats. and new Phillips 30 active sub. . I wish to use amp for mixing un my digital recording studio I have audio software for mixing in 5.1 Many thanks Jim Manning Spit Fire Audio Toronto

    Reply

    Re: JVC service or questions

     paul Posted Feb 08, 2005

    I have two jvc cameras that appears to have the same problem.WHEN SWITCHED TO THE CAMERA MODE II SAYS REMOVE LENS CAP,HOWEVER THE LENS CAPS WERE REMOVED. THERE IS NO IMAGE FROM THE CAMERA. I SUSPECT THE CCD UNITS OR THE RIBBON CABLE. PLEASE ADVISE ME.

    Reply

    I have a jvc vhs camcorder high resolution model #GR-SXM250U. When i remove the lens cap it still acts like its still on the lens cap notice light goes off but i still cant see anything i am at a loss here help.

    Reply

    Re: JVC service or questions

     Steve Posted Feb 07, 2005

    The model is JVS GR-SXM330 When I try to play the tape in the camcorder it says EO3 Unit in safeguard mode then it says, Remove and reatacth battery. Then when I take off the battery and put it back on i does the same exact thing over again. Then when I go to take the tape out of the camcorder, Some tape had came out of the tape. PLease Help Me!

    Reply

    Re: JVC service or questions

     lynn Posted Feb 06, 2005

    We have VCR/DVD player HR-XVC25U. The DVD is not working. We have always had a problem the the player stopping randomly. Now it will not work at all. We clean the DVD regularly. We now that the problem is not the disc because it works on our other DVD player. Please help as this is a problem and not a good representative of JVC products.

    Reply

    Re: JVC service or questions

     Bob Posted Feb 05, 2005

    Dear Stacy, I have a JVC model DR-MV1S. Before I send it in for servicing I have a question! When trying to record or play a dvd the machine will sometimes stop playing or recording and the display will start flashing loading. I haven't been able to record past 1/2 hour because this usually starts happening. I can't do anything else when this starts and have to wait awhile or shut things off. Any ideas?? Thanks alot.

    Reply

    Re: JVC service or questions

     Phil Posted Feb 04, 2005

    Hi Stacy I have a RX-517 Home Theater Amplifier, and my problem concerns a relay on the main amplifing board, it doesnt click. I've check the relay himself with an outboard supply, it's ok! So, i check his supply on the 2W resistance and the 24V required is ok! And don't know waht else to do! Please Help me Thanks Phil

    Reply

    I recently purchased a [used]grd 90 u camcorder,but it has no instructions...please if you know where I could get these?

    Reply

    Hi, I had a great little JVC shelf-top stereo. Recently I dropped it and it stopped working. I gave it to a friend to look at. He fixed it, apparently a fuse just popped out and that's all it was. Unfortunately it was stolen from his car b4 he could return it to me. Anyhow I don't have the model # or anything as it was on the receiver but I know it was manufactured in 1999. It was a small rectangular box size w/ a cd player that opened from the top. It had a volume dial on from that lit up blue when you turned it on. I believe it was able to play mp3's as well (could be wrong about that). Anyhow I have the speakers and the remote, and I would like to know how to replace it and if so, how much would it cost (whether it's worth it). I got your info from an Amazon search. Are you able to help me? Thank you very much, Jennifer Linch

    Reply

Pages:   « 1 2 3 523 524 525 526 527 528 529 643 644 645 »



  


© 2001-2012 - Pechorin's - Contact Us - Report a bug

Pechorin's does not take responsibility for the content of the messages published in the Forum.

RSS feed